Rough

This cotton spinning mill was one of many in Shaw and was opened in 1907 with power provided by this horizontal twin tandem compound steam engine by Scott & Hodgson of Guide Bridge. The cylinders were 18" & 42" x 5' (x2) and turned a 26' diameter flywheel driving by cotton ropes. The engine ran at 60 revolutions per minute and generated 1500 horsepower. It stopped running commercially in 1967 but was then preserved with the assistance of the Northern Mill Engine Society and was run on occasions until 1982 when the mill closed and was sold. Although the engine was made a Scheduled Ancient Monument it became very badly vandalised and was finally scrapped in 1994. This was a lovely engine and typical of so many in Lancashire. There are now only three large spinning mill engines surviving in situ.

This cotton spinning mill was one of many in Shaw and was opened in 1907 with power provided by this horizontal twin tandem compound steam engine by Scott & Hodgson of Guide Bridge. The cylinders were 18" & 42" x 5' (x2) and turned a 26' diameter flywheel driving by cotton ropes. The engine ran at 60 revolutions per minute and generated 1500 horsepower. It stopped running commercially in 1967 but was then preserved with the assistance of the Northern Mill Engine Society and was run on occasions until 1982 when the mill closed and was sold. Although the engine was made a Scheduled Ancient Monument it became very badly vandalised and was finally scrapped in 1994. This was a lovely engine and typical of so many in Lancashire. There are now only three large spinning mill engines surviving in situ.

This cotton spinning mill was one of many in Shaw and was opened in 1907 with power provided by this horizontal twin tandem compound steam engine by Scott & Hodgson of Guide Bridge. The cylinders were 18" & 42" x 5' (x2) and turned a 26' diameter flywheel driving by cotton ropes. The engine ran at 60 revolutions per minute and generated 1500 horsepower. It stopped running commercially in 1967 but was then preserved with the assistance of the Northern Mill Engine Society and was run on occasions until 1982 when the mill closed and was sold. Although the engine was made a Scheduled Ancient Monument it became very badly vandalised and was finally scrapped in 1994. This was a lovely engine and typical of so many in Lancashire. There are now only three large spinning mill engines surviving in situ.

This cotton spinning mill was one of many in Shaw and was opened in 1907 with power provided by this horizontal twin tandem compound steam engine by Scott & Hodgson of Guide Bridge. The cylinders were 18" & 42" x 5' (x2) and turned a 26' diameter flywheel driving by cotton ropes. The engine ran at 60 revolutions per minute and generated 1500 horsepower. It stopped running commercially in 1967 but was then preserved with the assistance of the Northern Mill Engine Society and was run on occasions until 1982 when the mill closed and was sold. Although the engine was made a Scheduled Ancient Monument it became very badly vandalised and was finally scrapped in 1994. This view shows the inverted vertical duplex barring engine that engaged with the gear ring on the rim of the flywheel. The wood boarding that covered the flywheel spokes is also seen. The flywheel consisted of two identical wheels running edge to edge each with its own set of spokes. This was typical of the larger wheels and the largest had three wheels set edge to edge as at Mons Mill, Todmorden. This was a lovely engine and typical of so many in Lancashire. There are now only three large spinning mill engines surviving in situ.

This cotton spinning mill was one of many in Shaw and was opened in 1907 with power provided by this horizontal twin tandem compound steam engine by Scott & Hodgson of Guide Bridge. The cylinders were 18" & 42" x 5' (x2) and turned a 26' diameter flywheel driving by cotton ropes. The engine ran at 60 revolutions per minute and generated 1500 horsepower. It stopped running commercially in 1967 but was then preserved with the assistance of the Northern Mill Engine Society and was run on occasions until 1982 when the mill closed and was sold. Although the engine was made a Scheduled Ancient Monument it became very badly vandalised and was finally scrapped in 1994. This was a lovely engine and typical of so many in Lancashire. There are now only three large spinning mill engines surviving in situ.

Dee Mill on the right was demolished long ago but the two Lily Mills on the left are part of a huge warehouse complex. The station is now part of a Metro but was then British Rail.

The Obelisk and what appears to be a damaged panorama table in Bishop Park

The view from Bishop Park up the valley from Slackcote to Denshaw village

What appears to be a panorama table with just the stone plinth remaining in Bishop Park. Grains Bar is beyond

Rather rough moorland for a park but it does contain a football pitch in this view from the Obelisk

View from the Crompton Circuit trail

Quite an extensive former farmhouse site

With Lower Doghill Farm in the centre of the view. Much of the grazing land is reverting to moorland reeds

On Buckstones Road and appeared to be in hibernation